Amp hook up to stock radio, quick links
Barry, Without knowing what vehicle you have, we can't help you with its speaker wiring. Does it need to go as far back as possible? As the typical subwoofer amplifier will be two or three times more powerful than the full-range amp in a system, that's where the greatest demand will occur, when the bass hits. Can someone please give me some guidance on next steps. Place the amp where you want it, dating someone that doesn't want then attach the ground black or brown wire to the amp.
So would I be able to use my fade control for the front and rear? You should be aware that this large a system in any vehicle will be a challenge to power. How should I connect the remote wire so that I don't have to disconnect it when I turn off the car? Safe as in not damaging the amp or sub. It's not until you're installing three or four devices that you start needing a relay.
Last thing you need is a dead battery. Warnings Be careful when around the electrical system of your car. No manufacturer does, that I know of. If you do install a relay, do not use the amplifier's constant power connection for it.
Video of the Day
Wayne, Not knowing the size of your factory alternator makes it a bit difficult to tell if you'll need a high-output alternator for your system when you add your amplifier. Seeing as this diagram only shows two amps, a relay is not show either. If you installed a powered sub, you will not need to connect the amplifier and speaker, as they are already connected.
How to hook up subs and amp to stock stereo in car
The diagram gives a generalized picture of how it connects. Chris, If you had bought your gear at Crutchfield, you could call Tech Support for free help troubleshooting your system. If your capacitors capable of enough farad, for both four channel amp and mono amp. Just cut the power wire, insert the inline fuse and reattach.
Please keep your phone line open. This will come into play later. Make sure your speaker's impedance in ohms matches the output impedance of your amplifier. My question, should i get A fuse or A fuse in line fuse holder near the battery? Is that supposed to work like that.
Why don't you give us a call and talk with an Advisor about possible solutions. Zach, casual dating or Wire each sub to its amp like this diagram. So I really need to get some good advice. Any recommendations are welcomed and appreciated. This was simple but invaluable.
Amplifier Wiring Diagrams How to Add an Amplifier to Your Car Audio System
- In this case, the patch cables that come from the receiver's subwoofer output would plug into the Epicenter's inputs.
- It looks like you're new here.
- Try moving your grounds to the same point and see if that doesn't clean things up.
- The fuse amperage should match the gauge size.
If you're only hooking up two speakers, even less. Dana, It sounds to me like everything you have is hooked up just fine and safely. Can i hook a sub up to that or do i need to get an aftermarket radio?
Currently only front doors and back dash speakers are functional how can I wires in the rear door speakers? What frequencies do you pick? Click on this link for details. It shows you how to add a subwoofer to a factory system.
Hook up amplifier to stock radio
If it is even questionable, I would rather just run new cables to the doors. Your help is always appreciated, thank you. Warnings Always Disconnect the Negative terminal from your battery before doing anything with electricity on your car.
If your headlights dim due to current draws from your system, you are better off putting the capacitors on your headlight circuit. Power on your car and stereo system and test your subwoofer for output. What is the best way and location to splice into the car with out taking away fro. How do I connect my new sub to my old amp?
Brooker, I'd have to know exactly what amplifiers you have and how powerful they are, in order to answer the question of what wiring to use. And do you see any problems with this set up? What happens to the factory wire that's installed in the factory speakers? Check the manuals included with your line-out converter, stereo and amplifier for complete installation instructions for your system.
Most people run one wire from the receiver to one amp, and then daisy-chain another wire to the second amp. This could be caused by a bad ground. That's why articles like this Amplifier Wiring Diagram exist, to guide customers in their own installation.
You can certainly add a powered sub to the system to improve the bass if the factory subwoofer amp isn't powerful enough for you. Juan, There is indeed a convenient, all-in-one wiring solution applicable to your situation. You should use a multi-meter to find the suitable connection spot.
Music is like candy, you have to get rid of the rappers to enjoy it. Please visit our Support page to find the help you need. Then to each individual amplifier.
Try it and if you think the bass overpowers the mids and highs, then you can bridge the channels to run the front speakers. Brand new battery and A alternator as well Any ideas i may be overlooked? With the Sony I have to choose from either having the rear or having the sub. The remote wire tells the amp to turn on.
If you bought your gear from Crutchfield, you could call Tech Support for free help with your system. Hi Buck its Josh again, thankyou for your help thus far. Brancker, If you're located on the Norfolk Island in the South Pacific Ocean, woman I'm afraid I can't offer any recommendations because I have no idea what gear is available to you.
If you are using a factory radio in your system, dating girl start by getting an amp with speaker-level inputs. Go to Corporate Sales page. Any help is much appreciated! You should be able to connect it to the auxiliary on the back of the stereo unit.
It Still Works
- Will this cause problems with bleeding or any other issues?
- Buck, Last question, I promise.
- Any suggestions as to why my tweeters are producing the sound they should be?
You would be best to tie into the rear channel, this can be done the stock head unit. Do you know if the stock speaker have connection for a Sub? My question is, do I need to upgrade my alternator or will the stock alternator be alright? You'd connect the factory radio's speaker output wires to the amp's inputs via a harness or adapter. Oh well, you can just pull the radio and tag the speakers there, you'll have to get an ignition source for the remote wire and its all behind the radio.